Skip to content

Cookie preferences

Choose which optional cookies the site may use. Necessary cookies are always on.

Inline measurement Marrari

Individual Industrial Moisture Sensor – UmiSense

In-line industrial moisture sensor with no electrical panel: it measures biomass, wood chips and other organics at one point of the line and sends the reading over Modbus RTU.

  • No panelModbus RTU straight to the PLC
  • 100 mmreading depth, 5 times/s
  • SS 304stainless housing with IP67 connector
UmiSense individual industrial moisture sensor by Marrari
What it is

What is the UmiSense industrial moisture sensor?

UmiSense is an individual industrial moisture sensor, made by Marrari in Brazil. Installed at one point of the line, it continuously measures the moisture of biomass, wood chips and other organics by the dielectric principle and sends the reading over Modbus RTU, with no electrical panel: just the sensor and the cables.

  • Zeroing, filters and recipes in UmiSetup4
  • Ready for PSi4
  • For whomBiomass cogeneration, pulp, grains and animal feed
  • SensorStainless steel housing, 150 × 150 mm area and 5 readings per second
  • IntegrationModbus RTU over RS485; ready for PSi4
  • RecipesAdjusted with the laboratory in the Tracker software
Why measure

Why measure moisture at one point of the line?

Because moisture changes the process result: in power generation, wet material burns worse and produces less steam; in grains and seeds, working at the moisture limit sells more, with mold risk under control. With continuous reading, adjustments are made on the spot.

  • Less wasted energy: real-time moisture control avoids burning water and overspending.
  • Continuous quality: off-spec material shows up right away, before it becomes waste.
  • More safety: moisture out of limits is corrected before it affects people and machines.

How long does material stay out of standard?

Between one sample and the next, nobody sees the moisture. Without continuous reading, a deviation only shows in the next sample, and all the material that passed until then is already out of standard. UmiSense reads the moisture of organic materials 5 times per second, at one point on the line. Change the sampling interval and compare.

How the line is measured
Sample every

With continuous reading, a deviation shows right away; with samples only, it shows in the next sample.

Simulation Example values, not readings from equipment.

Less material out of standard: the deviation shows right away, and the adjustment is made before it becomes waste.

Application

Where is UmiSense installed?

At various stages of production, where the material passes against the sensor face. The Marrari team helps choose the point where it is most effective. UmiSense is an industrial moisture sensor for organic materials, installed directly on the line.

The most common applications:

Cogeneration and energy · Pulp · Grains and seeds · Animal feed

  • Cogeneration and energybiomass, firewood, wood chips and residues in the boiler feed.
  • Pulpwood chips before the digester, with the reading sent straight to the PLC.
  • Grains and seedsworking at the moisture limit, with mold risk under control.
  • Animal feedfeed and meals at the dryer outlet, so they do not spoil in storage or lose mass from overdrying.
Principle

How does the sensor read moisture?

The UmiSense sensing face emits an electric field (dielectric method) that goes through up to 100 mm of the material passing against it, such as wood chips, biomass or other particulate organics. The water changes that field: the sensor reads the change 5 times per second and sends it over Modbus RTU, and the recipe set in UmiSetup4 converts the reading into moisture.

  1. Install the sensor

    In the line, with the material passing against the sensing face.

  2. Configure

    In the UmiSetup4 software: zeroing, filters and the material recipe.

  3. Read in real time

    5 readings per second, sent over Modbus RTU.

  4. Adjust with the lab

    In Tracker, with sample results of your material.

Customers

Who uses UmiSense

UmiSense is installed at one point on the line and measures the moisture of biomass, chips and other organic materials, with no electrical panel. Readings go via Modbus RTU straight to the PLC, and off-spec material is corrected before it becomes waste.

Company using the UmiSense: D'Italia Alimentos.

  • 100 mmreading depth
  • Less energywithout burning water or spending extra
  • Straight to PLCover Modbus RTU
  • 5/scontinuous readings instead of sampling

Companies using UmiSense

  • Suzano
  • Arauco
  • Ibema
  • Yerba Madre (Guayakí)
  • D'Itália Alimentos
  • Erva-Mate Giotti
Specifications

UmiSense specifications

Measurement

UmiSense specifications: Measurement
Measuring principledielectric; continuous reading
Measuring rangeadjustable, from 3 to 70% wet basis [the current sheet says 3 to 150% d.b. or 3 to 60% w.b.: to be confirmed by engineering]
Accuracybetter than 3 percentage points of moisture
Area and depth150 × 150 mm sensor area; 3.2 mm sensing face; reading up to 100 mm deep
Reading speed5 readings per second
Calibrationzeroing, filters and recipes in the UmiSetup4 software; recipes adjusted with the laboratory in Tracker

Installation and integration

UmiSense specifications: Installation and integration
CommunicationModbus RTU over RS485, to a PLC or SCADA; ready for PSi4
Housing304 stainless steel, 190 × 190 × 91 mm; 2.1 kg
Connector5-pin M12, IP67
Power supply24 VDC, 400 mA; no electrical panel
Temperatureoperation from −30 to 85 °C [the current sheet says sensor up to 80 °C and transmitter up to 50 °C: to be confirmed]
Warranty6 months
FAQ

Frequently asked questions about the industrial moisture sensor

Does the material need to touch the sensor?
Ideally, the material passes as close as possible to the sensing face, to avoid variations. The sensor reads up to 100 mm deep.
Can Marrari help with the calibration of the equipment?
Yes. The team assesses whether your material can be measured accurately and, once the equipment is purchased, calibrates it for your product with the UmiLab laboratory.
What is an industrial moisture sensor for?
To continuously measure the moisture of the material at one point of the line. UmiSense is used in biomass cogeneration and power plants and in processes from pulp to animal feed.
Can the sensor be adapted to my process?
Dimensions can be customized according to the process. [to be confirmed by engineering: other sizes besides the 190 × 190 × 91 mm box in the manual]
What is the UmiSense warranty?
6 months, like all Marrari systems and equipment. Parts and technical support are in Brazil, at the Marrari factory, so maintenance is quick and more affordable.
How does buying from outside Brazil work?
Payment is by international wire transfer (SWIFT) or international credit card. Freight can be arranged by the customer, or Marrari handles the entire export. Installation is carried out by the Marrari team or a local authorized partner.
Quote

Request a quote: UmiSense

Free and with no obligation. A Marrari specialist replies within 24 business hours.

  • Installation and integrationSimple: just the sensor and the cables, with no electrical panel, with the cables in a cable tray separate from the power cables. The Marrari team indicates the installation point.
  • 6-month warrantyFor all Marrari systems and equipment.
  • Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.
Request a quote