Skip to content

Cookie preferences

Choose which optional cookies the site may use. Necessary cookies are always on.

Inline measurement Marrari

In-Line Moisture Meter for Animal Feed – UmiPet

In-line moisture meter for animal feed: it measures the dryer outlet, second by second, so feed does not spoil in storage or lose mass from over-drying.

  • Dryermeasures the outlet, second by second
  • < 3 ppaccuracy on feed, flours and meals
  • 100recipes, one per product
UmiPet in-line moisture meter for animal feed by Marrari
What it is

What is the UmiPet in-line feed moisture meter?

UmiPet is Marrari’s in-line moisture meter for animal feed, for feed, flour and meal lines. A sensor installed at the dryer outlet measures moisture in real time using the dielectric principle, and the central unit sends the reading to the dryer control.

  • 304 stainless steel sensor, IP67 connector
  • Reads 100 mm deep
  • For whomAnimal feed, flour and meal plants
  • Sensor304 stainless steel, reading up to 100 mm deep
  • RecipesUp to 100, adjusted with the laboratory in Tracker
  • Integration4 × 4–20 mA outputs and Modbus RTU; Ethernet and Profibus optional
Why measure

Why control feed moisture?

Too wet, feed grows fungi and bacteria in storage and hurts the brand; too dry, it loses mass and quality. By measuring at the dryer outlet, you work close to the ideal value and gain mass without risking the product.

  • Safe, palatable feed: moisture on target, less risk of fungi and consistent nutritional quality.
  • Mass gain: drying only what is needed reduces cost and ingredient waste.
  • Instant adjustment: the dryer is corrected in real time, without waiting for the laboratory.

What does the sensor field see?

The plate emits a field that passes through up to 100 mm of the material. Change the water and the layer and see how the reading becomes moisture, and what that changes in the process.

reach 100 mm layer 100 mm 123
The field (2 and 3) goes through up to 100 mm of feed above the plate (1): it measures moisture inside the layer, not just the top kibble. That is why the feed layer over the sensor should be about 100 mm deep; with low flow, a collector gathers the sample.

Mass gain: drying only what is needed reduces cost and ingredient waste.

Close to the ideal value, you gain mass without risking the product.

Application

Where is UmiPet installed?

At the dryer outlet and at other points on the line, with the material passing next to the sensor. The Marrari team helps choose the most effective point. UmiPet measures feed moisture in line, so the dryer runs on target.

The most common applications:

Feed dryer outlet · Flours · Meals · Conveyors

  • Feed dryer outletdryer control by actual moisture.
  • Floursat the dryer outlet, on target, without losing mass from overdrying or molding in storage.
  • Mealsmeasured in the process, so formulation moisture stays the same in every batch.
  • Conveyorswith the sensor on the conveyor, the reading covers all the material passing by, with no sampling.
UmiPet in-line moisture sensor, in the same Marrari sensor housing used on UmiChip
Principle

How does UmiPet measure?

The sensor emits an electric field (dielectric method) that goes through up to 100 mm of the feed passing over it at the dryer outlet. The water in the feed changes that field: the central unit reads the change 5 times per second, compensates for temperature and converts it into moisture with each feed’s recipe.

  1. Install the sensor

    At the dryer outlet, on the conveyor or at another point on the line.

  2. Take samples

    Throughout the day, to compare with the laboratory.

  3. Adjust the recipe

    In the Tracker software, matching the reading to the test.

  4. Control the dryer

    With real-time moisture on the 4–20 mA outputs or via Modbus.

Software

Animal feed moisture: what does the UmiPet software show?

On the UmiPet supervisory screen, moisture from each sensor appears in real time, by batch, with reports by period. In Tracker, recipes are adjusted with laboratory samples.

To bring this meter and other plant equipment onto one screen, use the PSi4 supervisory system.

Actual software screen (in Portuguese).
How to read this screen
  1. The bars show the moisture read by each sensor.
  2. The blue bar identifies the batch: supplier, material, product and operator.
  3. The lower chart keeps the reading history, minute by minute.

Enlarged screen

Customers

Who uses UmiPet

At the dryer outlet, UmiPet measures the moisture of feed, flour or meal second by second. The dryer is corrected without waiting for the lab: feed does not spoil in storage or lose mass from overdrying.

Animal feed, flour and meal plants.

  • < 3 ppmoisture accuracy
  • Less energyused in the dryer, without overdrying
  • 5/scontinuous readings instead of sampling
  • 100 recipesprogrammable
Specifications

UmiPet specifications

Measurement

UmiPet specifications: Measurement
Measuring principledielectric, 5 readings per second, continuous or by collector
Materialsanimal feed, flours and meals
Measuring range3 to 150% dry basis or 3 to 70% wet basis; 0.1 percentage point resolution
Accuracybetter than 3 percentage points of moisture
Sensor reachup to 100 mm deep into the material

Installation and integration

UmiPet specifications: Installation and integration
Calibrationup to 100 programmable recipes, adjusted with laboratory samples (Tracker software)
Temperaturesensor up to 70 °C; central unit up to 50 °C; automatic compensation
Outputs and communication4 × 4–20 mA outputs; Modbus RTU (RS232/RS485); Ethernet and Profibus DP optional
Power supply95 to 240 VAC, 50/60 Hz; 500 W max.
ProtectionIP54 central unit; 304 stainless steel sensor (190 × 190 × 91 mm, 170 × 170 mm flange) with IP67 connector
FAQ

Frequently asked questions about the feed moisture meter

Does the material need to touch the sensor?
Ideally the product passes as close to the sensor as possible, to avoid variations. The sensor reads up to 100 mm deep.
Can I buy the meter with a ready recipe for my product?
Yes. Send a sample to the UmiLab laboratory, which creates the specific recipe for your product. Our team first assesses whether your material can be measured accurately and calibrates the equipment for your product.
What is the UmiPet warranty?
6 months, like all Marrari systems and equipment. Parts and technical support are in Brazil, at the Marrari factory, so maintenance is quick and more affordable.
How does buying from outside Brazil work?
Payment is by international wire transfer (SWIFT) or international credit card. Freight can be arranged by the customer, or Marrari handles the entire export. Installation is carried out by the Marrari team or a local authorized partner.
Quote

Request a quote: UmiPet

Free and with no obligation. A Marrari specialist replies within 24 business hours.

  • Installation and integrationBy the Marrari team, at the line point indicated for your process; the recipe calibration for your product is done with the laboratory.
  • 6-month warrantyFor all Marrari systems and equipment.
  • Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.
Request a quote