In-Line Volume, Moisture and Weight Meter – DensiDry
- Weightcalculated from volume and moisture
- 3%static volume accuracy
- 3 ppaverage moisture error
What is the DensiDry in-line volume and moisture meter?
DensiDry is Marrari’s
- Usually no changes to your line
- Up to 100 recipes
- For whomBiomass boilers in industry and power generation
- VolumeLaser scanner over the belt, 60 readings per second
- Moisture150 ×
150 mm sensor under the load, up to100 mm deep - Integration
4–20 mA, Modbus and Ethernet; Profibus optional
Why measure the biomass entering the boiler?
Wet chips force the boiler to evaporate water before burning, and it loses pressure; too much volume smothers combustion and puts pressure at risk. Knowing volume and moisture in real time lets you adjust the feed before the problem. See how biomass measurement systems work.
- More efficiency: the boiler gets just the right amount of fuel, no more and no less.
- Biomass on spec: each load’s moisture shows what will burn poorly before it enters the furnace.
- Less maintenance: fewer deposits and less corrosion caused by excess moisture.

Where is DensiDry installed?
On the belt feeding the boiler: the scanner sits on a bridge over the conveyor, without changing idlers or altering the belt, and the moisture sensor sits under the load. DensiDry shows biomass flow and biomass weight on the belt, together with moisture, on the way to the boiler.
Real-time volumehow much fuel goes in, so it is never smothered or short.Second-by-second moisturecorrected by laboratory tests.- Weight (optional)measuring the weight of the material on the belt.
- OEE and alertsrun and stop time, efficiency and alert
e-mails. - Belt safetyidler and belt deviations, before they become accidents.
- Other materialsorganic and some inorganic materials, assessed by engineering.
How does DensiDry measure?
Two sensors and a central unit: the laser scanner reads the load profile without contact, and the moisture sensor, using the dielectric principle, reads the material up to
- The laser reads volume
60 readings per second, unaffected by temperature, light or moisture.
- The sensor reads moisture
5 readings per second, inside the load, not just at the surface.
- The central unit calculates
Volume, moisture and weight, with each material’s curve (up to 100 recipes).
- Sends and alerts
To the PLC, the boiler and the SCADA system; OEE and alert
e-mails.
Biomass measurement system: what does the DensiDry software show?
On the DensiDry supervisory screen, biomass flow, moisture and density appear in real time, with the load profile and the history of what reached the boiler.
To bring this meter and other plant equipment onto one screen, use the PSi4 supervisory system.
How to read this screen
- The gauges show the flow, moisture and density of the biomass on the belt.
- The 3D load profile shows how the material is passing.
- On the left, material, quantities and energy; on the right, the history.
How to read this screen
- The windows open the reading history over time.
- You can see how the flow and moisture reaching the boiler varied.
- The panel stays behind, with the current readings.
Who uses DensiDry
3tentos (Rio Grande do Sul, Brazil) continuously measures the flow and moisture of the biomass feeding its boiler with Marrari’s system, then called VU. With fine control and automatic feed adjustments, it greatly reduced the biomass used to generate steam, says the utilities coordinator in the testimonial. Companies using the DensiDry: Bunge, Biosev, Cerradinho Bioenergia, Invivo Nutrição Animal and Oceana Minerais Marinhos.
- Less biomassfor the same steam (3tentos)
- Fine tuningof the feed, based on the data (3tentos)
- Higher yieldfrom the boiler, with moisture and flow measured
- 60/svolume readings
Companies using DensiDry
How much does biomass moisture cost in your boiler?
Wet biomass delivers less energy per tonne and lowers boiler efficiency: to make the same steam, the boiler burns more. Enter your boiler data and compare today’s moisture with your target. DensiDry shows biomass moisture and flow in real time, on the belt.
Want to measure this moisture on the belt? Request a quote
Calculator unlocked. Enter your process numbers.
DensiDry photos
Real photos of the equipment and installations. Click or tap a photo to enlarge it.
DensiDry specifications
Volume, moisture and weight
| Volume | laser scanner, |
|---|---|
| Belt width | up to |
| Volume accuracy | better than 3% of the measured value (static), depending on particle size |
| Volume calibration | with a sample of known volume or a body of known dimensions; with chips, every six months on average |
| Mounting | on a bridge over the conveyor, with adjustable supports; without altering the belt or changing idlers |
| Weight | optional: measuring the weight of the material on the belt |
| Moisture | dielectric principle; 150 × |
| Moisture range | adjustable, from 3 |
| Moisture accuracy | average error better than 3 percentage points |
Calibration and integration
| Moisture calibration | in line, compared with the laboratory; up to 100 recipes, one per material |
|---|---|
| Outputs and communication | |
| Central unit | 400 × 300 × |
Frequently asked questions about the biomass measurement system
Can I measure the weight of the material with the equipment?
Why use a biomass measurement system?
Does Marrari offer a biomass assessment?
What is the DensiDry warranty?
How does buying from outside Brazil work?
No question with that term. Try another word or talk to the team on WhatsApp.
Request a quote: DensiDry
Free and with no obligation. A Marrari specialist replies within 24 business hours.
- Installation and integrationBy Marrari engineering, on a bridge over the existing belt; in most cases, without modifying the line.
6-month warrantyFor all Marrari systems and equipment.- Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.





