Skip to content

Cookie preferences

Choose which optional cookies the site may use. Necessary cookies are always on.

Portable meters Marrari

Log and Firewood Moisture Meter – UmiLog

Log and firewood moisture meter: the probe measures the core, not just the bark, and estimates the net calorific value. For sawmills, pulp, charcoal and anyone who buys or burns firewood.

  • At corethe probe measures inside the log or firewood
  • NCVnet calorific value with the moisture
  • 5 to 10 sper reading, turning the probe in the hole
Measuring log moisture with the UmiLog M65 log and firewood moisture meter and its probe
What it is

What is the M65 UmiLog log and firewood moisture meter?

The M65 UmiLog is a portable log and firewood moisture meter, made by Marrari in Brazil. The probe goes into a 14 mm hole in the log and, turned for 5 to 10 seconds, shows the average moisture of the inside, not just the bark, and the net calorific value (NCV).

  • Recipes for eucalyptus and pine + 20 programmable
  • Weighs only 0.9 kg
  • Who it is forSawmills, pulp, charcoal and anyone who buys or burns firewood
  • MaterialsLogs and firewood, with recipes for eucalyptus and pine
  • Probe180 mm long, in a 14 mm hole at least 5 cm deep
  • RecordsUp to 5,000 readings in 100 batches, with UmiData reports
Why measure

Why measure the moisture of logs and firewood?

In a log, the dry bark is misleading: the water stays in the core. Measuring inside shows the wood you are buying and the energy the firewood will deliver, before you pay for water. See how and why to measure wood moisture.

  • Fair purchase: logs bought by weight or by dry mass (BDMT), with moisture measured on arrival.
  • Better burning: dry firewood gives more heat from less volume, with less smoke and less creosote in the chimney.
  • Less loss in the yard: wet wood rots and grows fungi; measured moisture guides drying and storage.
UmiLog M65 with the log probe
Application

Where should firewood and log moisture be measured?

From the receiving yard to the boiler. The M65 UmiLog measures the moisture of whole logs and firewood before the load goes on to the boiler.

The most common applications:

Log receiving · Firewood purchasing · Buying by weight or BDMT · Firewood calorific value · Charcoal, shavings and pulp · Drying and storage

  • Log receivingmoisture of each load on arrival.
  • Firewood purchasingpay for the wood, not the water.
  • Buying by weight or BDMTmoisture content to convert to dry mass.
  • Firewood calorific valueNCV estimated with the moisture.
  • Charcoal, shavings and pulpassess logs before processing.
  • Drying and storageplan air or kiln drying and store at the right point.
Logs stacked in the field, ready for moisture measurement with the M65 UmiLog
Principle

How does the probe measure the inside of the log?

The probe measures by the dielectric principle: the water in the wood changes the sensor’s electric field, and the recipe converts the reading into moisture and NCV, with automatic temperature compensation.

Video: how and why to measure the moisture of firewood, logs and biomass (in Portuguese)
  1. Drill the hole

    14 mm in diameter, radially, at least 5 cm deep. The drill bit is included.

  2. Insert and turn the probe

    For 5 to 10 seconds: it sweeps the inside of the log.

  3. Read the average

    Moisture and NCV on the display, with the wood recipe.

  4. Create the report

    Over USB, readings go to UmiData: batch, date and supplier.

Software

How does the UmiData software work?

UmiData is the data collection and reporting software of Marrari portable meters: M65 UmiLog readings become charts, batch statistics and Excel or PDF reports, plus the biomass price based on useful energy.

Real UmiData screen, with batches (Portuguese interface).
How to read this screen
  1. Each bar is one reading, in the order taken, and the red line is the batch average.
  2. The green band marks the target moisture. Next to it, the share of readings above, within and below it.
  3. Each batch shows the minimum, average and maximum and the fields you set up, such as wood, customer and supplier.

Enlarged screen

Customers

Who uses the UmiLog

When the load arrives, the UmiLog probe measures the core of the log or firewood and estimates the net calorific value. Purchases are based on dry mass, and only firewood that is ready goes to the burner.

Companies using the UmiLog: Lactalis, Inpasa, Seara, Bracell and CMPC.

  • 3 to 60%moisture on a wet basis (3 to 150% dry basis)
  • NCVnet calorific value with the moisture
  • 5 to 10 sper reading, with the probe in the hole
  • Wood, not waterpay for what actually burns

Companies using M65 UmiLog

  • Klabin
  • Cargill
  • Lactalis
  • Seara
  • Arauco
  • Bracell
Do the math

What is the firewood load that arrived really worth?

Wet firewood delivers less heat per tonne. Enter the contract moisture and the moisture measured with UmiLog and see the fair price for the energy, the same calculation as UmiData. See the calorific value of biomass.

Want to cut this loss? Request a quote

Use the calculator with your own process numbers

Enter your details to unlock the calculator. If you wish, a Marrari specialist can help you read the result.

By continuing, you agree to the terms of use and privacy. Marrari uses your data only to contact you about your solution.

Contract NCV—
Measured NCV—
Energy delivered—
Moisture (% wet basis): 0 to 60 NCV (kcal/kg)
NCV (kcal/kg) × Moisture (% wet basis): 0 to 60 contract measured load. The wetter it is, the less energy per kilo.
How the calculation works

LHV = GCV − 600 × (9 × H ÷ 100) and NCV = LHV × (1 − M) − 600 × M, in kcal/kg, with H = 6% hydrogen (typical of biomass) and M = moisture on a wet basis (fraction). Fair price = contract price × measured NCV ÷ contract NCV. GCV = gross calorific value; LHV = lower heating value; NCV = net calorific value.

GCVs are the UmiData table values for each wood; for black wattle and tropical hardwood, those from Costa Junior et al. (2023) and Quirino et al. (2005, average of 258 species); approximate values (see the article on calorific value). The M65 UmiLog estimates the NCV with the wood recipe, and UmiData runs the same price calculation with your load data.

Specifications

Technical specifications of the M65 UmiLog

Download data sheet (PDF, 375 KB) (opens in a new tab)

Measurement

Technical specifications of the M65 UmiLog: Measurement
Measuring principledielectric; probe inserted in a 14 mm radial hole (min. 5 cm) and turned for 5 to 10 s
Measuring range3 to 150% dry basis or 3 to 60% wet basis; resolution 0.1 percentage point
Accuracy±5 percentage points
Materialslogs and firewood; recipes for eucalyptus and pine plus 20 programmable ones
Calorific valueestimates the NCV, with the GCV and hydrogen content from the recipe
Calibrationrecipes adjusted with laboratory results in the Tracker software; annual calibration recommended at UmiLab

Instrument and data

Technical specifications of the M65 UmiLog: Instrument and data
Probe180 mm long and 13.2 mm in diameter; drill bit included
Temperatureoperation up to 70 °C, with automatic compensation
Memoryup to 5,000 readings in up to 100 batches
Communication and softwareUSB to PC; UmiData (moisture and NCV reports in Excel or PDF)
Battery3.7 V 1,800 mAh lithium-polymer; 6 h continuous use; 5 h charging
Weight and display0.9 kg; backlit 2.2" LCD
FAQ

Frequently asked questions about the log moisture meter

Can I calibrate the meter myself?
Yes. With the Tracker software, you adjust the recipe with laboratory results from your wood (curve, offset, wet or dry basis, GCV and hydrogen), and UmiData creates the reports and history. The Marrari team shows you how to use both, and UmiLab does the recommended annual calibration.
Why measure moisture inside the log and not on the surface?
Because the surface dries first and is misleading: the probe sweeps the inside of the log and calculates the average, which works on both wet and dry logs.
What are the UmiData software and UmiData Server?
It is the UmiLog’s data collection and reporting software: it organizes readings by batch and date, creates and analyzes recipes and exports reports, charts and tables to Excel or PDF. UmiData Server is the network version: readings from all meters are stored in a central SQL database that any computer on the plant network can access, which also makes ERP and MES integration easier.
What is the UmiLog warranty?
6 months, like all Marrari systems and equipment. Parts and technical support are in Brazil, at the Marrari factory, so maintenance is quick and more affordable.
Does Marrari offer a biomass assessment?
Yes, free of charge, for anyone generating energy and steam with firewood or biomass: the team evaluates how the fuel is used and suggests how to make it more efficient and economical. Request the assessment. Outside Brazil, the assessment is carried out by a consultant from Marrari’s foreign trade (COMEX) team.
Does Marrari offer UmiLog training?
Yes. User training can be live and is scheduled for the day and time you choose, with no fixed date: book it on the trainings page, stating your equipment.
How does buying from outside Brazil work?
Payment is by international wire transfer (SWIFT) or international credit card. Freight can be arranged by the customer, or Marrari handles the entire export.
Quote

Request a quote: M65 UmiLog

Free and with no obligation. A Marrari specialist replies within 24 business hours.

  • Installation and integrationNone needed: the UmiLog is portable and arrives ready to measure, with the drill bit, charger and USB cable.
  • 6-month warrantyFor all Marrari systems and equipment.
  • Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.
Request a quote