Wood Kiln Drying Manager – EcoPower
Wood kiln drying manager for multiple kilns: smooth curves, conditioning sprays and smart fan reversal, with the boiler’s steam consumption under control.
- 25phases of drying curve for your wood
- 15%less steam per dried m³ (customer report)
- Woodflat, without warping or checking
What is the EcoPower wood kiln drying manager?
EcoPower is Marrari’s wood kiln drying manager, for plants with several kilns. Besides controlling each kiln, it manages the process energy, with the boiler’s steam consumption and the fans, to reduce thermal and electrical energy use.
- Remote access via local network or internet
- Logs every minute
- For whomWood drying plants with several kilns
- Drying25 phases and curves by DB × WB, RH, EMC or PS
- EnergyBoiler steam, fans and economy mode
- LoggingAlarms, interruptions and parameters with the person responsible
Why manage the whole drying operation?
Each kiln controlled on its own competes for steam with the others and strains the boiler. By managing them together, the boiler runs smoothly, steam goes where it is needed and the wood dries on target, without thermal shock.
- Less steam and energy: with the boiler and fans managed, one customer cut steam from 0.91
to 0.77 t per m³ of dried wood (15.49%), and another reports 20% less steam flow. - Flat wood: smooth curves and water and steam sprays, without warping or checking. At Grupo Ipumirim, cracks and stress fell by up to 40%.
- Shorter drying: about 20% less time at Tramontina; at another customer, cycles went from
99–105 h to65–72 h.
What does each kiln reading show?
The
What it shows:
Why: The controller compares this value with the phase target, to decide what to drive.
Features: alarms for a dry wet bulb and for a reference
What it shows: Equilibrium moisture (shown as UE) and drying potential (shown as PS), on each side.
Why: They offer another way to run the drying: the curve can be programmed by TBS × TBU, TBS × UR, TBS × UE or TBS × PS.
What it shows: The radiator valve opening, from 0
Why: It brings the temperature to the phase value, on a ramp, so the transition is not abrupt.
Features: at the start, temperature can follow humidity, to avoid a harsh environment. With the kiln stopped, the valve opens at intervals to keep the radiator free of condensate, which prevents water hammer.
What it shows: The air vent opening, from 0
Why: It changes the kiln air, to remove the moisture leaving the wood.
Features: smart damper. With the temperature below target, the damper starts to close, to help with heating.
What it shows: The speed, with a frequency inverter, and the time until the next reversal.
Why: Reversing the airflow each cycle alternates the side receiving air, so the load dries evenly. At peak hours, the fans can stop, slow down or simply not reverse.
Features: two peak periods per day, holiday dates with no stop and ramp reheat after the stop.
Beyond
What it shows: The intensity of the steam spray and the sprinkler, from 0
Why: They restore air humidity when the TBU falls below target. They work in cycles, to give the humidity time to even out in the kiln.
What it shows: The water tub intensity, from 0
Why: One more way to restore air humidity: it turns on when the TBU falls below target, also in cycles. It can also be used to change the wood color and even out its tone.
What it shows: Wood moisture at each point measured in the load.
Why: It shows where the load is wetter and drier, without opening the kiln. A phase can end by time and/or by wood moisture.
Features: at the end of a phase, the cycle can go to an extra conditioning phase.
Beyond
What it shows: The average of the load moisture points.
Why: It runs the cycle on a single number. The average can use all points, the driest, the wettest or one chosen point, and it can discard the extremes.
What it shows: The variation between the load moisture points (shown as VRU).
Why: It shows whether the load is drying evenly, and it can take the cycle to a conditioning phase.
Beyond
What it shows: The temperature of the water feeding the sprinkler (optional sensor).
Why: It keeps the water at the target temperature; outside the tolerated range, the system warns.
What it shows: The boiler steam pressure (optional sensor).
Why: Below the minimum pressure set, the system raises the
Beyond
Beyond
What it shows: Whether economy mode is on.
Why: It activates the routines that save thermal and electrical energy.
Simulation Example values, not readings from equipment.
What does EcoPower manage?
The kilns, the boiler and the fans, in the SCADA system and the PLC. Wood drying management stays in a single system, from each kiln’s curve to the boiler’s steam consumption.
Boiler manager · Fan manager · Economy drying mode · Smart damper · Extra phases and reheating · VRU use · Remote access · Phytosanitary report (optional)
- Boiler managersteam consumption distributed among the kilns on each line, by pressure, by flow or by both, with priority to the lowest phase or the widest valve opening.
- Fan managersmart
start-up and reversal. - Economy drying modeto reduce energy consumption.
- Smart damperhelps during heating.
- Extra phases and reheatingextra conditioning, ramp reheating and new heating after long stops.
- VRU usefor extra conditioning phases and phase completion.
- Remote access
multi-user via local network or internet, with an access log. - Phytosanitary report (optional)a separate module, for export certification.
How does drying work?
You program the curves and phases; each kiln’s PLC runs the drying, and the manager handles the energy of the whole set, logging everything in the database minute by minute.
- Program the curve
DB × WB, RH, EMC or PS, with up to 25 phases.
- The PLC runs it
Heating, drying, equalizing, conditioning and cooling.
- EcoPower manages
Boiler steam, fans and economy mode.
- Log and follow
Alarms, interruptions and operator, over the network or internet.
A real drying cycle, hour by hour
DB is the air temperature in the kiln. WB shows air humidity: the closer it is to DB, the more humid the air. Learn about dry and wet bulb.
Hour 24 of the cycle
See the values every 12 hours
| Hour | Dry bulb (DB), °C | Wet bulb (WB), °C | Average wood moisture, % |
|---|---|---|---|
| 0 | 73% | ||
| 12 | 85% | ||
| 24 | 65% | ||
| 36 | 60% | ||
| 48 | 51% | ||
| 60 | 43% | ||
| 67 | 28% |
Kiln drying manager software: what does EcoPower show?
On the EcoPower supervisory screen, you follow each kiln in real time, program drying curves and check the history and events of each load, without walking to the kiln.
To bring the kilns and other plant equipment onto one screen, use the PSi4 supervisory system.
How to read this screen
- The drawing shows a
cross-section of the kiln, with the fan, the heating and the wood stacks. - Each numbered point in the stack is a sensor, with the wood moisture at that spot and the average beside it.
- On the side, the
dry-bulb andwet-bulb temperatures, relative humidity and the current curve phase.
How to read this screen
- On the left, each steam line with pressure and flow, marked in yellow, and the high and low limits.
- In the middle, the curve stages on each line: heating, drying, finishing, extras and reheating.
- On the right, a card for each kiln on the line, with pressure, flow, phase and valve opening.
How to read this screen
- At the top, steam flow; at the bottom, boiler pressure, over the same 24 hours.
- Flow varies through the day, while pressure stays close to
9.5 kgf/cm² in this record. - The diamonds mark the highest and lowest values; the red line shows the trend.
How to read this screen
- The chart shows the whole cycle, from the start to the end of drying.
- Each color is a reading: temperatures, wood moisture and target values.
- At the top, the start, end, and total and net duration of the cycle.
How to read this screen
- Each column is a drying phase, and each row is a programmed value.
- The rows show temperatures, ramps and fan speed.
- Under completion, you set when the phase ends: by time, by wood moisture or by both.
How to read this screen
- Each row is an event: phase, operator action, end of drying or communication failure.
- The report gives the date, time, kiln, cycle and duration of each one.
- You filter by period and kiln to find what happened in each load.
Who uses EcoPower
Madeireira Ponte Alta, in Brazil, shortened drying times, improved wood quality and increased output, first with
“We have been a partner since the beginning of EcoPower […] we needed to reduce energy, and with the system we save 20% to 25%.”
20–25% energy savings (Famossul)- ≈ 20%shorter drying time (Tramontina)
- +
500 m³ dried per month after moving fromNew Smart (Ponte Alta) - Up to 40%fewer cracks and less stress (Grupo Ipumirim)
Companies using EcoPower
How much can EcoPower save on your drying?
Enter your drying data and biomass price. The calculation estimates the savings from lower steam consumption.
Steam used per m³ of dried wood
Want to cut this loss? Request a quote
Calculator unlocked. Enter your process numbers.
EcoPower specifications
Drying control
| Phases | 25 programmable phases: heating, drying, equalizing, conditioning and cooling; extra conditioning phases |
|---|---|
| Curve | programmable by dry bulb (DB) against wet bulb (WB), relative humidity (RH), equilibrium moisture content (EMC) or drying potential (PS) |
| Heating | ramp reheating; new heating (phase 1) after long stops; smart damper |
| Fans and sprays | speed, cycle and spray time independent per phase; smart reversal |
| Energy | economy drying mode; boiler steam consumption manager, by line (pressure, flow or both; priority to the lowest phase or the widest valve opening); fan manager |
| Actuators | independent activation; compatible with on/off, proportional and motorized actuators |
Logging and options
| Logging | |
|---|---|
| SCADA | |
| Optional sensors | boiler pressure, steam flow, electrical energy, sprinkler pump pressure, compressed air, hot water tank, weather station and 2 extra |
| Modules | included: |
| Power supply | |
| Warranty | 6 months |
What changes between EcoPower, New Smart and New Easy
| Feature | EcoPower | ||
|---|---|---|---|
| Drying phases + reheating | 23 + 2 | 16 + 1 | 15 |
| Curve programming | DB × WB, RH, EMC or PS | DB × WB, RH, EMC or PS | DB × WB |
| Independent commands per phase | 5, with water tub | 5, with water tub | 4, no water tub |
| Extra conditioning phases | Yes | Yes | No |
| Smooth reheating after stops and peak hours | Yes | Yes | No |
| Conditioning by the variation of the moisture points | Yes | Yes | No |
| Smart damper during heating | Yes | Yes | No |
| Dry radiator, free of condensate | Yes | Yes | No |
| Automatic removal and return of faulty wet bulbs | Yes | Yes | No |
| Holidays in scheduled stops | Yes | Yes | No |
| Virtual boiler pressure sensor | Yes | Yes | Optional |
| Alarms by email | Yes | Yes | Optional |
| Virtual sensors | Yes | Optional | Optional |
| Events by email | Yes | Optional | Optional |
| Yes | Optional | Optional | |
| Steam consumption manager | Yes | No | No |
| Fan manager: start and reversal | Yes | No | No |
| Smart reversal, by wood moisture | Yes | No | No |
| Economy mode: thermal and electrical energy | Yes | No | No |
| Yes | No | No | |
| Control of the variation between points (VRU) | Yes | No | No |
| Automatic removal and return of moisture points | Yes | No | No |
| Advance selection of the next cycle’s curve | Yes | No | No |
All 3 share: target × actual in real time,
Frequently asked questions about the wood kiln drying manager
What are the benefits of automating wood drying?
How much steam does EcoPower save?
Are consulting and training included?
What is the EcoPower warranty?
How does buying from outside Brazil work?
No question with that term. Try another word or talk to the team on WhatsApp.
Request a quote: EcoPower
Free and with no obligation. A Marrari specialist replies within 24 business hours.
- Installation and integrationBy the Marrari team, compatible with different kilns and actuators. Consulting and user training with partner CPM Suporte are included in the package.
6-month warrantyFor all Marrari systems and equipment.- Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.











