Skip to content

Cookie preferences

Choose which optional cookies the site may use. Necessary cookies are always on.

Inline measurement Marrari

In-Line Moisture Meter for Sugarcane Bagasse – UmiCana

In-line moisture meter for sugarcane bagasse: it measures bagasse on the belt, second by second, to adjust mill imbibition and keep the boiler fire from being smothered.

  • Millmeasures at the outlet, to adjust imbibition
  • < 3 ppaccuracy on bagasse
  • 100 mmreads inside the bagasse layer
UmiCana in-line moisture meter for sugarcane and sugarcane bagasse by Marrari
What it is

What is the in-line moisture meter for sugarcane bagasse?

UmiCana is Marrari’s in-line moisture meter for sugarcane bagasse, for sugar, ethanol and cogeneration plants. A sensor under the belt measures the moisture of the whole bagasse layer, not just the surface, by the dielectric principle, at the mill outlet or at the boiler feed.

  • AISI 304 stainless sensor, IP67 connector
  • Up to 100 recipes
  • Who it is forSugar and ethanol mills and bagasse cogeneration
  • SensorAISI 304 stainless steel, reads up to 100 mm deep
  • RecipesUp to 100, adjusted with the lab in Tracker
  • Integration4 × 4–20 mA outputs and Modbus RTU; optional Ethernet and Profibus
Why measure

Why measure bagasse moisture?

For two reasons. At the mill, bagasse moisture shows whether extraction is right and guides the adjustment of the imbibition valves. At the boiler, bagasse that is too wet smothers combustion and destabilizes the process. See how to measure sugarcane bagasse moisture.

  • Maximum extraction: imbibition adjusted to the real bagasse moisture.
  • More steam and cogeneration: bagasse on target burns better and generates more energy.
  • Stable boiler: less incomplete combustion, fouling and blockages.

What does the sensor field see?

The plate emits a field that passes through up to 100 mm of the material. Change the water and the layer and see how the reading becomes moisture, and what that changes in the process.

reach 100 mm layer 100 mm 123
The field (2 and 3) goes through up to 100 mm of bagasse above the plate (1): it measures moisture inside the layer, not just at the surface. That is why the bagasse layer over the sensor should be about 100 mm deep; with low flow, a collector gathers the sample.

Maximum extraction: imbibition adjusted to the real bagasse moisture.

Where the material goes

With imbibition adjusted to real moisture, extraction reaches its maximum.

Application

Where is UmiCana installed?

On the belt, the conveyor, the dryer or another point on the line, with the bagasse passing close to the sensor. UmiCana measures sugarcane bagasse moisture in line, continuously.

The most common applications:

Mill outlet · Boiler feed · Cogeneration · Sugarcane by-products

  • Mill outletbagasse moisture to adjust imbibition.
  • Boiler feedbagasse measured on its way to the furnace; too wet, it smothers combustion.
  • Cogenerationbagasse on target burns better and makes more steam and electricity.
  • Sugarcane by-productsstraw and other materials on the line, with the material recipe.
Sugarcane mill, where UmiCana measures bagasse moisture
Principle

How does UmiCana measure?

The sensor emits an electric field (dielectric method) that goes through up to 100 mm of the bagasse passing over it on the belt. The water in the bagasse changes that field: the central unit reads the change 5 times per second, compensates for temperature and converts it into moisture with the bagasse recipe.

  1. Install the sensor

    On the bagasse belt or conveyor.

  2. Collect samples

    Throughout the day, to compare with the lab.

  3. Adjust the recipe

    In the Tracker software, matching the reading to the lab test.

  4. Control the process

    Imbibition and boiler, through the 4–20 mA outputs or Modbus.

Software

Sugarcane bagasse moisture: what does the UmiCana software show?

On the UmiCana supervisory screen, moisture from each sensor appears in real time, by batch, with reports by period. In Tracker, recipes are adjusted with laboratory samples.

To bring this meter and other plant equipment onto one screen, use the PSi4 supervisory system.

Actual software screen (in Portuguese).
How to read this screen
  1. The bars show the moisture read by each sensor.
  2. The blue bar identifies the batch: supplier, material, product and operator.
  3. The lower chart keeps the reading history, minute by minute.

Enlarged screen

Customers

Who uses UmiCana

At the mill outlet, UmiCana measures bagasse moisture on the belt, second by second. With the actual moisture, imbibition is adjusted for higher extraction, and bagasse reaches the boiler ready to burn well, without smothering the furnace.

Companies using the UmiCana: Usina Delta, Biosev, Jalles Bioenergia, Zillo Lorenzetti and Usina Cerradão.

  • < 3 ppmoisture accuracy
  • 5/scontinuous readings instead of sampling
  • In real timebagasse moisture on the conveyor
  • 100 mmreading depth

Company using UmiCana

  • Delta Sucroenergia
Specifications

Technical specifications of UmiCana

Measurement

Technical specifications of UmiCana: Measurement
Measuring principledielectric, 5 readings per second, continuous or with sampler
Materialssugarcane bagasse, at the mill outlet or boiler feed
Measuring range3 to 150% dry basis or 3 to 70% wet basis; 0.1 percentage point resolution
Accuracybetter than 3 percentage points of moisture
Sensor reachup to 100 mm deep into the material

Installation and integration

Technical specifications of UmiCana: Installation and integration
Calibrationup to 100 programmable recipes, adjusted with laboratory samples (Tracker software)
Temperaturesensor up to 70 °C; central unit up to 50 °C; automatic compensation
Outputs and communication4 × 4–20 mA outputs; Modbus RTU (RS232/RS485); optional Ethernet and Profibus DP
Power supply95 to 240 VAC, 50/60 Hz; 500 W max.
ProtectionIP54 central unit; AISI 304 stainless steel sensor (190 × 190 × 91 mm, 170 × 170 mm flange) with IP67 connector
FAQ

Frequently asked questions about the bagasse moisture meter

Does the material need to touch the sensor?
Ideally the bagasse passes as close as possible to the sensor, to avoid variations. The sensor reads up to 100 mm deep.
Can I buy the meter with a ready recipe for my product?
Yes. Send a sample to the UmiLab laboratory, which creates the specific recipe. Our team first assesses whether your material can be measured accurately and calibrates the equipment for your product.
What is the UmiCana warranty?
6 months, like all Marrari systems and equipment. Parts and technical support are in Brazil, at the Marrari factory, so maintenance is quick and more affordable.
Does Marrari offer a biomass assessment?
Yes, free of charge, for anyone generating energy and steam with biomass: the team evaluates how the fuel is used and suggests how to make it more efficient and economical. Request the assessment. Outside Brazil, the assessment is carried out by a consultant from Marrari’s foreign trade (COMEX) team.
How does buying from outside Brazil work?
Payment is by international wire transfer (SWIFT) or international credit card. Freight can be arranged by the customer, or Marrari handles the entire export. Installation is carried out by the Marrari team or a local authorized partner.
Quote

Request a quote: UmiCana

Free and with no obligation. A Marrari specialist replies within 24 business hours.

  • Installation and integrationBy the Marrari team, at the point of the line chosen for your mill; the recipe is calibrated with the laboratory.
  • 6-month warrantyFor all Marrari systems and equipment.
  • Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.
Request a quote