Skip to content

Cookie preferences

Choose which optional cookies the site may use. Necessary cookies are always on.

Kiln automation Marrari

Wood Kiln Drying Controller – New Easy

Wood kiln drying controller for small plants: it runs the kiln on its own, phase by phase, saving steam and energy, so the wood comes out without warping or cracking.

  • 15curve phases, for small plants
  • Woodno warping or cracking
  • No PCcan also run on the PLC alone
New Easy wood kiln drying controller supervisory screen
What it is

What is the New Easy wood kiln drying controller?

New Easy is a wood kiln drying controller for small plants, made by Marrari in Brazil. It controls kiln temperature and humidity and runs the heating, drying, equalizing, conditioning and cooling phases on its own, with SCADA on a PC or with the PLC alone.

  • Phases end by time and/or moisture
  • 16 wood groups
  • Who it is forSmall and medium wood drying plants
  • KilnsDifferent kiln types and actuators
  • SCADASV-520 on a PC, with access over the network or internet
  • RecordsMinute-by-minute database, alarms and interruptions
Why measure

Why automate wood drying?

Manual drying misses both ways: wet wood comes back, over-dried wood warps and cracks. With fine control of each phase, the kiln uses less steam and energy, dries faster and delivers the wood on target.

  • Less steam and energy: temperature and humidity adjusted automatically in each phase.
  • Defect-free wood: uniform drying, with less warping, cracking and rejects.
  • Shorter drying: smooth transitions between phases and real-time remote monitoring.

What does each kiln reading show?

The real-time screen shows each part of the kiln. Tap each element to see what it shows and why.

What it shows: Dry-bulb temperature (shown as TBS), wet-bulb temperature (shown as TBU) and relative humidity (shown as UR), on each side.

Why: The controller compares this value with the phase target, to decide what to drive.

Understand dry bulb and wet bulb

Simulation Example values, not readings from equipment.

Application

What does New Easy offer?

Tools for fine drying control, in the SCADA and in the PLC. It is kiln automation for drying wood with the essentials: the curve, the phases and the record of every cycle.

What the controller does:

Setpoint × actual · Decimals · Independent phases · E-mail alarms (optional) · Remote access · Protected PLC · Extra sensors · Phytosanitary report (optional)

  • Setpoint × actualmonitoring of the control variables and actuator positions.
  • Decimalson every monitored quantity, for fine curves.
  • Independent phasesfan speed and cycle and spray time per phase.
  • E-mail alarms (optional)PLC alarms and diagnostics sent by e-mail.
  • Remote accessmulti-user over the local network or internet, with an access log.
  • Protected PLCremote software upload and memory restore.
  • Extra sensorssteam flow, boiler pressure, electric power, weather station and more.
  • Phytosanitary report (optional)a separate module, for export certification.
Wood drying kiln with the door open and the stacks of boards in the load, where New Easy automates the drying
Principle

How does drying work?

You program the drying curve by dry-bulb and wet-bulb temperature (DB × WB) and the phases; the PLC drives heating, fans, sprays and vents and logs everything in the database.

Video: the New Easy wood drying controller (in Portuguese)
Marrari electrical panel with the PLC, display and keypad on the door
Electrical panel with the Marrari PLC, which runs the kiln drying.
  1. Program the curve

    DB × WB and up to 15 phases, with decimals.

  2. The PLC runs it

    Heating, drying, equalizing, conditioning and cooling.

  3. Follow it

    On the SV-520 SCADA, over the network or internet.

  4. Keep records

    Minute by minute, with alarms, interruptions and who was in charge.

A real drying cycle, hour by hour

DB is the air temperature in the kiln. WB shows air humidity: the closer it is to DB, the more humid the air. Learn about dry and wet bulb.

Hour 24 of the cycle

A real cycle recorded by the supervisory system of a kiln with New Smart (kiln 06, cycle 350, May 2022): average wood moisture starts at 73%, reaches about 85% in the first 8 hours, during heating, and ends at 28%, after 67 hours. New Easy also logs the kiln readings minute by minute in the database. Approximate values, read from the report, without momentary drops.
See the values every 12 hours
Cycle readings every 12 hours
HourDry bulb (DB), °CWet bulb (WB), °CAverage wood moisture, %
037 °C28 °C73%
1267 °C58 °C85%
2468 °C58 °C65%
3669 °C58 °C60%
4872 °C58 °C51%
6072 °C55 °C43%
6776 °C61 °C28%
Software

Wood kiln drying system: what does New Easy show?

On the New Easy supervisory screen, you follow each kiln in real time, program drying curves and check the history and events of each load, without walking to the kiln.

To bring the kilns and other plant equipment onto one screen, use the PSi4 supervisory system.

Actual software screen (in Portuguese).
How to read this screen
  1. The drawing shows a cross-section of the kiln, with the fan, the heating and the wood stacks.
  2. Each numbered point in the stack is a sensor, with the wood moisture at that spot and the average beside it.
  3. On the side, the dry-bulb and wet-bulb temperatures, relative humidity and the current curve phase.

Enlarged screen

Customers

Who uses New Easy

In kilns at small plants, New Easy runs drying on its own, adjusting temperature and humidity in each curve phase. The wood comes out without warping or cracking, using less steam and energy.

Companies using the New Easy: Caeté Florestal, Brasiltropical Pisos, Imapa, Madelotto and Salvaro.

  • Energysaves steam and power in every phase
  • 15 phasesof programmable drying
  • No PCruns on the PLC alone
  • On the curvethe kiln follows the set drying curve

Companies using New Easy

  • Tramontina
  • Salvaro
  • Reflorestadores Unidos
  • Famossul
  • VL Garcia Madeiras
Specifications

Technical specifications of New Easy

Drying control

Technical specifications of New Easy: Drying control
Phases15 programmable drying phases: heating, drying, equalizing, conditioning and cooling, with phase switching
Curveprogrammable by dry-bulb × wet-bulb (DB × WB); optional 2nd wet bulb; 16 wood groups (species); phase ends by time and/or wood moisture
Actuatorsindependent activation; works with on/off, proportional and motorized actuators
Fans and spraysfan speed and cycle and spray time set independently per phase
Operationbasic settings stored in the PLC; option to run with the PLC only; local alarms
SCADASV-520 on a PC; multi-user access over the local network or internet, with an access log

Records and options

Technical specifications of New Easy: Records and options
Recordsminute-by-minute database; alarms, interruptions, power outages, operator and maintenance; parameters sent to the PLC with the person responsible
Notificationslocal alarms; PLC alarms and diagnostics by e-mail (optional)
Optional sensorssteam flow, boiler pressure (also virtual), electric power, sprinkler pump pressure, compressed air, hot water tank, weather station and 2 extra 4–20 mA inputs
Modulesoptional, not included: ECO-PRO (production manager), virtual sensors and phytosanitary report
Power supply220/380 VAC, 500 VA
Warranty6 months

What changes between EcoPower, New Smart and New Easy

Differences between EcoPower, New Smart and New Easy
FeatureEcoPowerNew SmartNew Easy
Drying phases + reheating 23 + 216 + 115
Curve programming DB × WB, RH, EMC or PSDB × WB, RH, EMC or PSDB × WB
Independent commands per phase 5, with water tub5, with water tub4, no water tub
Extra conditioning phases YesYesNo
Smooth reheating after stops and peak hours YesYesNo
Conditioning by the variation of the moisture points YesYesNo
Smart damper during heating YesYesNo
Dry radiator, free of condensate YesYesNo
Automatic removal and return of faulty wet bulbs YesYesNo
Holidays in scheduled stops YesYesNo
Virtual boiler pressure sensor YesYesOptional
Alarms by email YesYesOptional
Virtual sensors YesOptionalOptional
Events by email YesOptionalOptional
ECO-PRO, production manager YesOptionalOptional
Steam consumption manager YesNoNo
Fan manager: start and reversal YesNoNo
Smart reversal, by wood moisture YesNoNo
Economy mode: thermal and electrical energy YesNoNo
Multi-zone control YesNoNo
Control of the variation between points (VRU) YesNoNo
Automatic removal and return of moisture points YesNoNo
Advance selection of the next cycle’s curve YesNoNo

All 3 share: target × actual in real time, minute-by-minute logging in a SQL Server database, multi-user access over the network or internet, scheduled stops, integration with moisture meters, 8 or 12 moisture points per kiln and an optional phytosanitary report.

FAQ

Frequently asked questions about the wood drying controller

What are the benefits of automating wood drying?
Steam and energy savings, shorter drying times, less waste and wood without warping or cracking, with fine adjustments throughout the process. Marrari has over 30 years of experience in wood drying, with support, courses and consulting from its partner CPM Suporte.
Does New Easy work without a computer?
Yes: the basic settings are stored in the PLC, and it can run on the PLC alone. The PC SCADA adds the records and remote access.
Does Marrari offer drying consulting and training?
Yes, together with CPM Suporte, a wood drying consulting and training company: to shorten drying times and save steam, energy and biomass. Outside Brazil, Marrari’s export team coordinates the service.
What is the New Easy warranty?
6 months, like all Marrari systems and equipment. Spare parts and technical support are in Brazil, at the Marrari factory, so maintenance is quick and more affordable.
How does buying from outside Brazil work?
Payment is by international wire transfer (SWIFT) or international credit card. Freight can be arranged by the customer, or Marrari handles the entire export. Installation is carried out by the Marrari team or a local authorized partner.
Quote

Request a quote: New Easy

Free and with no obligation. A Marrari specialist replies within 24 business hours.

  • Installation and integrationBy the Marrari team, compatible with different kiln types and actuators. To get the most out of it, drying consulting and training with partner CPM Suporte.
  • 6-month warrantyFor all Marrari systems and equipment.
  • Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.
Request a quote