Wood Moisture Meter – M55-56bt Sword
Wood moisture meter with a
1.1 m sword: measures inside the stack85 °C max. operating temperature, even in the kiln- 3
to 75% moisture, dry basis
What is the M55-56bt Sword wood moisture meter?
The
- Bluetooth, USB and EcoPower integration
- ±1 p.p. on pine
- Who it is forDrying kilns, sawmills and pallet plants
- SpeciesPine and other species, density 100
to 1,200 kg/m³ - In the kilnOperation up to
85 °C, with automatic compensation - RecordsUp to 3,000 readings in 100 batches, with UmiData reports
Why measure moisture inside the stack?
The center of the stack is the last to dry: measuring only the outside boards is misleading. With the sword you measure the core of the load, decide whether it can leave the kiln and avoid pulling samples with a forklift. See how and why to measure wood moisture.
- Fewer rejects: the average of several boards shows a load that is too wet, which molds, or too dry, which warps.
- Drying on target: readings inside the chamber, to act on the drying without opening the load.
- Safer inspection: no forklift to pull samples, with less risk and less labor.
Where is the wettest board in the stack?
In the middle: a stack dries from the outside in, and measuring only the outer boards is misleading. Move the drying forward, slide the sword in and compare the edge with the core, without taking the load apart.
The edge of the stack dries first and the middle dries last: that is where the sword shows whether the load is ready.
On the meter, holding OK starts automatic collection: one reading per second as the sword goes in.
Where does the Sword make a difference?
Wherever wood is stacked. The
Inside the kiln · Stacks and packages · Pallets · Load sorting · Kiln inlet and outlet · Drying faults
- Inside the kilnsamples in the drying chamber, to act on the process.
- Stacks and packagesmoisture of the boards inside the stack.
- Palletsaverage of several boards at once, including before HT treatment.
- Load sortingroute each load by its moisture.
- Kiln inlet and outletcheck the load before and after drying.
- Drying faultsfind the spot in the stack that did not dry.

How does the Sword work?
The sensor measures by the dielectric principle, at the sword tip (inside the stack) or at the meter base; the chosen density converts the reading into moisture. In the bt version, the sword talks to the meter over Bluetooth.
- Choose the density
The species density, from 100
to 1,200 kg/m³. - Insert the sword
Between the boards, in the middle of the stack or pallet.
- Read and save
Moisture on the display, saved to the batch; or continuous automatic collection.
- Create the report
Over USB or Bluetooth, in UmiData, or integrated with EcoPower.
How does the UmiData software work?
UmiData is the data collection and reporting software of Marrari portable meters:
How to read this screen
- Each bar is one reading, in the order taken, and the red line is the batch average.
- The green band marks the target moisture. Next to it, the share of readings above, within and below it.
- Each batch shows the minimum, average and maximum and the fields you set up, such as wood, customer and supplier.
How to read this screen
- The curve shows how the readings spread around the batch average.
- The 1σ, 2σ and 3σ deviations tell whether the batch is uniform or has pieces far from the average.
- The same batch also appears as a histogram: how many readings fall in each moisture range.
Who uses the Sword
The sword goes into the stack, pallet or package, even inside the kiln, and measures several boards from the inside without breaking down the batch. Drying is checked in the middle of the load, with no forklift needed to pull samples.
Companies using the
- 3
to 75% moisture, dry basis 1,098 mm sword, to measure inside the stack- No unstackingreads moisture inside the stack
- Wirelesssword connected over Bluetooth
Companies using
M55-56bt Sword photos
Real product photos. Click or tap a photo to enlarge it.
Technical specifications of the M55-56bt Sword
Measurement
| Measuring principle | dielectric; reading at the sword tip (inside the stack) or at the meter base |
|---|---|
| Measuring range | 3 |
| Accuracy | ±1 percentage point on pine |
| Species | pine and other species, adjusted by density |
| Calibration | apparent density at 0% adjustable from 20 to 120 (100 |
| Reach |
Instrument and data
| Temperature | operation up to |
|---|---|
| Communication and software | Bluetooth and USB; UmiData (Excel or PDF reports); integration with EcoPower |
| Memory | up to 3,000 readings in 100 batches; continuous automatic collection |
| Battery | |
| Dimensions and mass | M55bt: 160 × 80 × |
| Warranty | 6 months |
Frequently asked questions about the sword moisture meter
Can I calibrate the meter myself?
What are the UmiData software and UmiData Server?
Are a sword hygrometer and a sword moisture meter the same thing?
What is the M55-56bt warranty?
How does buying from outside Brazil work?
Does Marrari offer M55-56bt Sword training?
No question with that term. Try another word or talk to the team on WhatsApp.
Request a quote: M55-56bt Sword
Free and with no obligation. A Marrari specialist replies within 24 business hours.
- Installation and integrationNone needed: the
M55-56bt is portable and arrives ready to measure, with the sword, charger and USB cable. 6-month warrantyFor all Marrari systems and equipment.- Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.









