Wood Kiln Drying Controller – New Smart
Wood kiln drying controller, Marrari’s traditional system, now on the PowerServer platform: fine curves, sensor alarms and the kiln followed remotely.
- 16+1phases of drying curve for your kiln
- Wooduniform, without warping or cracking
- Alarmssensor alarms, with remote access
What is the New Smart wood kiln drying controller?
- Dry radiator routine prevents water hammer
- SQL Server records
- Who it is forSmall, medium and large drying plants
- Drying16+1 phases and 4 curve types
- SensorsDry
wet-bulb and referencedry-bulb fault alarms - PlatformPowerServer, with access over the network or internet
Why automate wood drying?
With automatic control, the kiln adjusts temperature and humidity on its own in each phase: less steam and energy, shorter drying and uniform wood, without warping or cracking.
- Less steam and energy: drying conditions adjusted automatically and scheduled stops, with fans off, at lower speed or without reversal.
- Uniform wood: fine control of temperature and humidity and smooth transitions between phases, with fewer defects and losses.
- Problems caught early: sensor alarms and
real-time remote monitoring.
What does each kiln reading show?
The
What it shows:
Why: The controller compares this value with the phase target, to decide what to drive.
Beyond
Beyond
What it shows: Equilibrium moisture (shown as UE) and drying potential (shown as PS), on each side.
Why: They offer another way to run the drying: the curve can be programmed by TBS × TBU, TBS × UR, TBS × UE or TBS × PS.
What it shows: The radiator valve opening, from 0
Why: It brings the temperature to the phase value, on a ramp, so the transition is not abrupt.
Beyond
What it shows: The air vent opening, from 0
Why: It changes the kiln air, to remove the moisture leaving the wood.
Beyond
What it shows: The speed, with a frequency inverter, and the time until the next reversal.
Why: Reversing the airflow each cycle alternates the side receiving air, so the load dries evenly. At peak hours, the fans can stop, slow down or simply not reverse.
Beyond
What it shows: The intensity of the steam spray and the sprinkler, from 0
Why: They restore air humidity when the TBU falls below target. They work in cycles, to give the humidity time to even out in the kiln.
Beyond
What it shows: The water tub intensity, from 0
Why: One more way to restore air humidity: it turns on when the TBU falls below target, also in cycles. It can also be used to change the wood color and even out its tone.
What it shows: Wood moisture at each point measured in the load.
Why: It shows where the load is wetter and drier, without opening the kiln. A phase can end by time and/or by wood moisture.
Beyond
What it shows: The average of the load moisture points.
Why: It runs the cycle on a single number. The average can use all points, the driest, the wettest or one chosen point, and it can discard the extremes.
Beyond
What it shows: The variation between the load moisture points (shown as VRU).
Why: It shows whether the load is drying evenly, and it can take the cycle to a conditioning phase.
What it shows: The temperature of the water feeding the sprinkler (optional sensor).
Why: It keeps the water at the target temperature; outside the tolerated range, the system warns.
What it shows: The boiler steam pressure (optional sensor).
Why: Below the minimum pressure set, the system raises the
Simulation Example values, not readings from equipment.
What does New Smart offer?
Dry radiator · Dry wet bulb ·
- Dry radiatorroutine that removes condensate and prevents water hammer, which damages steam traps and line strainers.
- Dry wet bulbalarm and automatic deactivation or activation.
Dry-bulb faultalarm for a faulty sensor or reversed fans.- Smart damperhelps with heating.
- Scheduled stopsat 2 times a day, with holiday dates with no stop and ramp reheat after the stop.
- Extra phasesfor conditioning, with fans and sprays per phase.
- Remote access
multi-user over the network or internet, with access levels and a log. - Phytosanitary report (optional)a separate module, for export certification.
How does drying work?
You program the curve and the phases; the kiln PLC runs the drying and the SCADA logs everything in the database minute by minute, with
- Program the curve
DB × WB, RH, EMC or PS, with 16+1 phases.
- The PLC runs it
Heating, drying, equalizing, conditioning and cooling.
- Follow it
Setpoint × actual and actuator positions, over the network or internet.
- Keep records
Alarms, interruptions, operator and maintenance, minute by minute.
A real drying cycle, hour by hour
DB is the air temperature in the kiln. WB shows air humidity: the closer it is to DB, the more humid the air. Learn about dry and wet bulb.
Hour 24 of the cycle
See the values every 12 hours
| Hour | Dry bulb (DB), °C | Wet bulb (WB), °C | Average wood moisture, % |
|---|---|---|---|
| 0 | 73% | ||
| 12 | 85% | ||
| 24 | 65% | ||
| 36 | 60% | ||
| 48 | 51% | ||
| 60 | 43% | ||
| 67 | 28% |
Kiln drying controller software: what does New Smart show?
On the
To bring the kilns and other plant equipment onto one screen, use the PSi4 supervisory system.
How to read this screen
- The drawing shows a
cross-section of the kiln, with the fan, the heating and the wood stacks. - Each numbered point in the stack is a sensor, with the wood moisture at that spot and the average beside it.
- On the side, the
dry-bulb andwet-bulb temperatures, relative humidity and the current curve phase.
How to read this screen
- Each column is a drying phase, and each row is a programmed value.
- The rows show temperatures, ramps and fan speed.
- Under completion, you set when the phase ends: by time, by wood moisture or by both.
How to read this screen
- Each row is an event: phase, operator action, end of drying or communication failure.
- The report gives the date, time, kiln, cycle and duration of each one.
- You filter by period and kiln to find what happened in each load.
Who uses New Smart
Madeireira Ponte Alta, in Brazil, started with
- 2,400 → 3,000m³ dried per month (Madeireira Ponte Alta)
- Fewer cracksand less warping in the wood
- 16+1 phasesof programmable drying
- Email alarmsand PLC diagnostics
Companies using
Technical specifications of New Smart
Drying control
| Phases | 16+1 programmable phases: heating, drying, equalizing, conditioning and cooling; extra conditioning phases |
|---|---|
| Curve | programmable by dry bulb (DB) against wet bulb (WB), relative humidity (RH), equilibrium moisture content (EMC) or drying potential (PS); 16 wood groups (species); phase ends by time and/or wood moisture; smooth transitions between phases |
| Heating | smart damper; ramp reheat after a scheduled shutdown |
| Fans and sprays | fan speed and cycle and spray time set independently per phase |
| Protections | dry radiator routine, which prevents water hammer; dry |
| Actuators | independent activation of heating, damper, steam spray, sprinkler and water tub; works with on/off, proportional and motorized actuators |
Records and options
| Controller | CP 300 PLC, developed by Marrari |
|---|---|
| Wood moisture | 8 or 12 points per kiln; integration with portable and |
| Records | SQL Server database, minute by minute; one decimal place on all readings; alarms, interruptions, power outages, operator and maintenance; parameters sent to the PLC with the person responsible |
| Notifications and access | PLC alarms and diagnostics by |
| Optional sensors | 2nd wet bulb, steam flow, boiler pressure, electric power, sprinkler, compressed air, hot water tank, weather station and 2 extra |
| Modules | optional, not included: |
| Power supply | |
| Warranty | 6 months |
What changes between EcoPower, New Smart and New Easy
| Feature | EcoPower | ||
|---|---|---|---|
| Drying phases + reheating | 23 + 2 | 16 + 1 | 15 |
| Curve programming | DB × WB, RH, EMC or PS | DB × WB, RH, EMC or PS | DB × WB |
| Independent commands per phase | 5, with water tub | 5, with water tub | 4, no water tub |
| Extra conditioning phases | Yes | Yes | No |
| Smooth reheating after stops and peak hours | Yes | Yes | No |
| Conditioning by the variation of the moisture points | Yes | Yes | No |
| Smart damper during heating | Yes | Yes | No |
| Dry radiator, free of condensate | Yes | Yes | No |
| Automatic removal and return of faulty wet bulbs | Yes | Yes | No |
| Holidays in scheduled stops | Yes | Yes | No |
| Virtual boiler pressure sensor | Yes | Yes | Optional |
| Alarms by email | Yes | Yes | Optional |
| Virtual sensors | Yes | Optional | Optional |
| Events by email | Yes | Optional | Optional |
| Yes | Optional | Optional | |
| Steam consumption manager | Yes | No | No |
| Fan manager: start and reversal | Yes | No | No |
| Smart reversal, by wood moisture | Yes | No | No |
| Economy mode: thermal and electrical energy | Yes | No | No |
| Yes | No | No | |
| Control of the variation between points (VRU) | Yes | No | No |
| Automatic removal and return of moisture points | Yes | No | No |
| Advance selection of the next cycle’s curve | Yes | No | No |
All 3 share: target × actual in real time,
Frequently asked questions about the wood kiln drying controller
What are the benefits of automating wood drying?
Does New Smart prepare drying for Industry 4.0?
Does Marrari offer drying consulting and training?
What is the New Smart warranty?
How does buying from outside Brazil work?
No question with that term. Try another word or talk to the team on WhatsApp.
Request a quote: New Smart
Free and with no obligation. A Marrari specialist replies within 24 business hours.
- Installation and integrationBy the Marrari team, compatible with different kilns and actuators. To get the most out of it, drying consulting and training with partner CPM Suporte.
6-month warrantyFor all Marrari systems and equipment.- Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.








