Skip to content

Cookie preferences

Choose which optional cookies the site may use. Necessary cookies are always on.

Inline measurement Marrari

In-Line Moisture Meter for Mate Herb – UmiMate

In-line moisture meter for mate herb: it measures the dryer outlet in real time, so you never store wet mate, which heats up and spoils, and keep the flavor of every batch.

  • Dryermeasures the herb at the outlet, in real time
  • < 3 ppaccuracy on mate herb
  • SS 304stainless sensor with IP67 connector
UmiMate in-line moisture meter for mate herb by Marrari
What it is

What is the UmiMate in-line mate herb moisture meter?

UmiMate is Marrari’s in-line moisture meter for mate herb (yerba mate), for mate processing plants. A flat sensor after the dryer measures the moisture of all the mate passing over it using the dielectric principle, and the signal controls the dryer or triggers alarms for the operator.

  • Reads up to 100 mm deep into the material
  • Up to 100 recipes
  • For whomMate processing plants and bulk organics industries
  • SensorFlat, 304 stainless steel, reading up to 100 mm deep
  • RecipesUp to 100, adjusted with the laboratory in Tracker
  • Integration4 × 4–20 mA outputs and Modbus RTU; Ethernet and Profibus optional
Why measure

Why measure mate herb moisture?

Mate that leaves the dryer with high moisture heats up in storage (exothermic effect) and is lost. By measuring at the outlet, the dryer is adjusted right away, the mate stores well and the flavor stays consistent from batch to batch.

  • Safe storage: no wet mate heating up and spoiling in storage.
  • Consistent flavor: the same drying point in every batch.
  • Instant adjustment: the dryer corrected by the reading, with process traceability.

What does the sensor field see?

The plate emits a field that passes through up to 100 mm of the material. Change the water and the layer and see how the reading becomes moisture, and what that changes in the process.

reach 100 mm layer 100 mm 123
The field (2 and 3) goes through up to 100 mm of herb above the plate (1): it measures moisture inside the layer, not just the top leaves. That is why the herb layer over the sensor should be about 100 mm deep; with low flow, a collector gathers the sample.

Consistent flavor: the same drying point in every batch.

On target, the herb stores well, and the flavor stays consistent from batch to batch.

Application

Where is UmiMate installed?

At a strategic point in the process, with the mate passing over the sensor; the most common is the conveyor at the dryer outlet. It also works for other bulk organics, with its own recipe. UmiMate measures mate herb moisture in line, right after drying.

The most common applications:

Dryer outlet · Conveyor belts · Other plant points · Other bulk organics

  • Dryer outletdryer control by actual moisture.
  • Conveyor beltscontinuous reading of the moving mate.
  • Other plant pointsherb receiving and storage, where moisture decides flavor and keeping quality.
  • Other bulk organicsother organics moving on the belt, with a recipe created by UmiLab from a sample.
Marrari UmiMate panels installed beside the mate herb line
Principle

How does UmiMate measure?

The flat sensor emits an electric field (dielectric method) that goes through up to 100 mm of the mate herb leaving the dryer and passing over it. The water in the herb changes that field: the central unit reads the change 5 times per second, compensates for temperature and converts it into moisture with the herb recipe.

  1. Install the sensor

    On the conveyor, at the dryer outlet.

  2. Take samples

    Throughout the day, to compare with the laboratory.

  3. Adjust the recipe

    In the Tracker software, matching the reading to the test.

  4. Control the dryer

    Via the 4–20 mA outputs or Modbus, or with alarms to the operator.

Software

Mate herb moisture: what does the UmiMate software show?

On the UmiMate supervisory screen, moisture from each sensor appears in real time, by batch, with reports by period. In Tracker, recipes are adjusted with laboratory samples.

To bring this meter and other plant equipment onto one screen, use the PSi4 supervisory system.

Actual software screen (in Portuguese).
How to read this screen
  1. The bars show the moisture read by each sensor.
  2. The blue bar identifies the batch: supplier, material, product and operator.
  3. The lower chart keeps the reading history, minute by minute.

Enlarged screen

Customers

Who uses UmiMate

At the dryer outlet, UmiMate measures mate herb moisture in real time. The dryer is corrected on the spot: herb does not go wet into storage, where it heats up and spoils, and every batch comes out at the same point.

Companies using the UmiMate: Ervateira Giotti and Guayaki y Mate Brasil.

  • < 3 ppmoisture accuracy
  • Less energyused in the dryer, without overdrying
  • 5/scontinuous readings instead of sampling
  • 100 recipesprogrammable

Companies using UmiMate

  • Yerba Madre (Guayakí)
  • Erva-Mate Giotti
Specifications

UmiMate specifications

Measurement

UmiMate specifications: Measurement
Measuring principledielectric, 5 readings per second, continuous or by collector
Materialsmate herb (yerba mate) and other bulk organic materials
Measuring range3 to 150% dry basis or 3 to 70% wet basis; 0.1 percentage point resolution
Accuracybetter than 3 percentage points of moisture
Sensor reachup to 100 mm deep into the material

Installation and integration

UmiMate specifications: Installation and integration
Calibrationup to 100 programmable recipes, adjusted with laboratory samples (Tracker software)
Temperaturesensor up to 70 °C; central unit up to 50 °C; automatic compensation
Outputs and communication4 × 4–20 mA outputs; Modbus RTU (RS232/RS485); Ethernet and Profibus DP optional
Power supply95 to 240 VAC, 50/60 Hz; 500 W max.
ProtectionIP54 central unit; 304 stainless steel sensor (190 × 190 × 91 mm, 170 × 170 mm flange) with IP67 connector
FAQ

Frequently asked questions about the mate herb moisture meter

Does the material need to touch the sensor?
Ideally the mate passes as close to the sensor as possible, to avoid variations. The sensor reads up to 100 mm deep.
Can I buy the meter with a ready recipe for my product?
Yes. Send a sample to the UmiLab laboratory, which creates the calibration curve and the recipe. Our team first assesses whether your material can be measured accurately and calibrates the equipment for your product.
What is the UmiMate warranty?
6 months, like all Marrari systems and equipment. Parts and technical support are in Brazil, at the Marrari factory, so maintenance is quick and more affordable.
How does buying from outside Brazil work?
Payment is by international wire transfer (SWIFT) or international credit card. Freight can be arranged by the customer, or Marrari handles the entire export. Installation is carried out by the Marrari team or a local authorized partner.
Quote

Request a quote: UmiMate

Free and with no obligation. A Marrari specialist replies within 24 business hours.

  • Installation and integrationBy the Marrari team, at the line point indicated for your plant; the calibration curve and recipe are made with the laboratory.
  • 6-month warrantyFor all Marrari systems and equipment.
  • Support and calibrationSupport in Brazil and Latin America; new recipes from the UmiLab laboratory.
Request a quote